TY  - THES
T1  - Investigation of fluidised bed coating : measurement, optimisation and statistical modelling of coating layers
A1  - van Kampen,Andreas
Y1  - 2018/08/21
N2  - Fluidised bed coating describes a process to encapsulate particles. The coating layer is applied in order to protect the core material from chemical reactions with the environment, to control the release of drugs or to mask bad taste. Depending on the application, the coating layer must fulfil various quality requirements, such as completeness, homogeneity and minimum layer thickness.
The measurement of the coating layer thickness is therefore necessary in order to determine appropriate parameters for an optimal coating process. This, however, is difficult in the investigated core particle size range of 100 to 500 μm with a coating layer thickness of around 10 μm. Fluorescent imaging of sliced particles or imaging of optical slices using confocal laser scanning microscopy are possible ways to make the coating layer visible and to measure the coating layer thickness using image analysis techniques. This leads to detailed images of the coating layer and an accurate description of the coating layer thickness distribution, but is rather time consuming due to tedious sample preparation and long image acquisition times. Consequently only relatively few particles are measured and used to draw conclusions on the population. Other methods like measurement of the change of particle size using laser diffraction or assessment of the volume ratio of coating to core material usually only deliver the mean thickness and no information on completeness and homogeneity of the coating.
In the first part of this thesis a quick method for coating thickness measurement was developed based on a dissolution test. Sodium chloride was used as a core material and maltodextrin DE21 was used as a coating material. When dissolved in deionised water, sodium chloride raises the conductivity in contrast to maltodextrin. Therefore, the measurement of conductivity can be used to assess the dissolution curve of the core material. The coating layer delays the dissolution of the core and by comparison with the dissolution curve of pure sodium chloride the coating thickness distribution can be assessed by deconvolution.
It was shown that this method is well reproducible and delivers reliable results comparable to other methods. The method is fast, which enables the measurement of many samples with replicates and using appropriate sample division should provide a good representation of the population. The shape of the thickness distribution allows the quantification of the three aforementioned quality parameters. The method was therefore used in the second part of this thesis in order to investigate the coating process using design of experiments.
The four factors spray rate, air temperature, air velocity and concentration of the coating solution were investigated using a central composite design of experiments. The dissolution method was used to assess the coating quality. The particle size distribution was measured in order to quantify the agglomeration rate and the mass of deposited coating material was assessed by quantifying a tracer colour in order to assess the efficiency of the process. Significant quadratic models were fitted to all response variables. These were successfully used to find a local optimum within the investigated parameter space which allowed the formation of an optimal coating layer within a short time frame.
The results of the previous investigations showed that the thickness distribution can be well described by a Weibull distribution. Furthermore, it was possible to confirm effects that were previously described in the literature, i.e. that a low concentration of the coating solution leads to more homogeneous coating layers. In order to give a general description of the coating layer, a statistical model of the coating thickness distribution was developed in the third part of this thesis and verified by a Monte-Carlo simulation.
The model reproduces the experimentally determined effect of the concentration of the coating solution qualitatively and is able to calculate the mean thickness distribution with given concentration, contact angle, sprayed mass and core particle and droplet size. Appropriate adjustments of these parameters lead to a good agreement between the model and measured thickness distributions of real experiments. It was concluded that predominant spray drying of small droplets and an increase of concentration of the remaining droplets due to pre drying negatively affects the homogeneity of the coating layer. 
It was further confirmed that the Weibull distribution can be used to describe the coating layer thickness in the investigated thickness range. The thickness distribution transitions from the Weibull distribution to a normal distribution as the coating becomes thicker. Thin coatings with defects can be described by a clinched Weibull distribution containing the uncoated area fraction as an offset.
KW  - Wirbelschicht
KW  - Befilmen
KW  - Modellierung
KW  - Methode
KW  - Optimierung
CY  - Hohenheim
PB  - Kommunikations-, Informations- und Medienzentrum der Universität Hohenheim
AD  - Garbenstr. 15, 70593 Stuttgart
UR  - http://opus.uni-hohenheim.de/volltexte/2018/1508
ER  -